NO:857296,BLCG 26SS two-way zipper closure embroidered plaid jacket This product is made of custom-made yarn-dyed plaid original fabric. It needs to complete four pre-processing processes of ultra-dense pre-shrinking, weft density correction, tension leveling, and flat-width shaping before being put into production. The shrinkage error of the fabric's longitude and latitude is strictly controlled within 0.2, which completely eliminates the hidden dangers of plaid deformation and alignment deviation after the garment is worn, laying an irreplaceable foundation for the whole piece to align. The pretreatment time of a single fabric is three times that of an ordinary jacket. The core process difficulty is the full-area interlocking technology, which requires all exposed pieces such as the front and rear panels of the garment, large and small sleeve panels, lapel collars, pocket flap welts, placket stops, and side seam panels to achieve horizontal penetration of horizontal grids, vertical alignment of vertical grids, complete mirror symmetry of left and right panels, and strict alignment tolerances. It is controlled within 0.1mm, and the industry standard is only 0.5mm. The cutting piece layout adopts zero-loss precise positioning method, and the loss rate of a single fabric is increased by 20. Any deviation of the cutting grain will be judged as a defective product, and the experience and accuracy requirements of the cutting master have reached a strict level. At the structural level, it is equipped with a two-way double-head customized zipper opening and closing system. The zipper chain and placket pattern need to be 100% aligned in the center seam. When the zipper is installed, the plaid alignment and stop smoothness are simultaneously completed to prevent the plaid from being pulled or skewed due to zipper installation. Front loop Sportsicon heavy industry embroidery adopts positioning embedded technology. The embroidery stitches must accurately follow the warp and weft direction of the check pattern, and the positioning error of the embroidery frame does not exceed 0.05mm. The floating embroidery process avoids the stitch tension from pulling the fabric texture, and achieves the perfect symbiosis between the embroidery pattern and the check texture. The entire garment adopts segmented alignment sewing and full-process quality inspection and control. From cutting to finished product, it needs to undergo 7 alignment checks. Every seam, structural line, and decorative piece serves the integrity of the pattern. The complexity of the process, labor cost, and quality control standards are all benchmarked against the high-end garment level. It has both pioneering design and unrepeatable craftsmanship. Sizes 46-52,,jackets & coats,jackets & coats,19860909BLCG 26SS双向拉链开合刺绣格纹夹克外套 本品采用定制色织格纹原布,投产前需完成超密预缩、纬密校正、张力匀整、平幅定型四道前置预处理工序,将面料经纬度缩率误差严控在0.2以内,彻底消除成衣穿着后的格纹形变、对位偏移隐患,为全件对格奠定不可替代的基础条件,单面料预处理工时即为普通外套的3倍. 核心工艺难点为全域贯通对格技术,要求衣身前后片、大小袖片、翻领领面、袋盖贴边、门襟止口、侧缝拼块等所有外露裁片,实现横格水平贯通、竖格垂直对齐、左右片完全镜像对称,对位公差严格控制在0.1mm以内,行业常规标准仅为0.5mm.裁片排料采用零损耗精准定位法,单款面料损耗率提升20,任何一处裁片纹路偏移即判定为次品,对裁剪师傅的经验与精度要求达到严苛级别. 结构层面搭载双向双头定制拉链开合系统,拉链齿链与门襟格纹需实现中缝百分百对齐,拉链安装时同步完成格纹对位与止口平顺处理,杜绝拉链安装导致的格纹拉扯、歪斜.正面loop sportsicon重工刺绣采用定位嵌入式工艺,刺绣针迹需精准贴合格纹经纬走向,绣框定位误差不超过0.05mm,通过浮动刺绣工艺避免针脚张力拉扯面料纹路,实现刺绣图案与格纹肌理的完美共生. 整件成衣采用分段对位缝制、全工序质检管控,从裁片到成品需经过7次对位校验,每一处拼接缝、结构线、装饰件均服务于对格完整性,工艺复杂度、人工成本、品控标准均对标高定成衣级别,兼具先锋设计与不可复制的匠心做工. 尺码46-52,,jackets & coats,jackets & coats,,Men's clothing